Search results

I will go out in the garage tomorrow and take a closer look at mine. In either case, the Rough Country Mollie panels did fit, but they do touch the bottom of the bed which is what I was expecting anyway so it didn't make me believe anything was different or wrong.

My rails and cover were installed by Toyota, so I don't believe anything is relocated with the exception of the rails being about 5/16th" away from the wall because the cover S hooks are using the same mounting bolts as the rails. All looks to me to be the same for the rails with or without the...

I have a 2024 Tacoma TRD Pro with the OEM Tonneau cover and installed the Rough Country "Molle Panel Kit | Bed | Toyota Tacoma 4WD (2024)" on the cab and sides of the bed. The rails remain where they were, but did need to get loosened to mount the panels. There were some tight spots, but not...

I now carry a portable 12v/120v tire inflator and a 20' AC power cord. It all just fits nicely in my rear bed panel compartment on the passenger side. I also have a portable deflator and coupler to use with my inflator that I take with me as needed. Nice to have the right tools to do the job...

I found out my Pro was set at 46psi when trying to overcome deep snow a month after I got my truck which didn't fair that well off-road. I now have it set at the factory setting of 32psi and the ride is much better.

$490.00 for a set of 4? That is outrageously expensive.

I believe one advantage is that I believe the Toyota maps is GPS based which might be helpful when you are in areas with limited cell phone coverage.

Where were you able to get the "TRD Pro" tailgate inserts?

Project still in the works, but I did finish the Toyota pigtail jumper. This is the original Toyota Jumper. Unpinned the Black wire (AUX1) and pinned the White wire (AUX3) using a similar pin as used in the Toyota harness. I believe this pin is a 621-2-2A Using my own 3 pin waterproof...

Bed mat for me. Thank you!

I like all the products, but would love to win the 14" Dash Tray.

Will do. It has to work. Just wish I had 2 wires in the harness from the engine compartment to the rear which would then open up more possibities like I understand the 2025's have. The 2024's only have 1 wire. I also have just installed, but not yet connected, a 6 gang AuxBeam Switch which...

You could use 2 of these for only $8.60 and still have 8 left over for other uses. It should easily fit on the existing cover but would only give you brake, DRL, or AUX switch lighting. There are many similar products available where you could find White if you only want a reverse light...

Not yet, it is on my list of things to do on my Truck and around the house and yard. Honeydo season is here. :sadface:

I am going to give this 2 power Amber one a try and use the low connection with my other DRL lighting. It also has a High Brightness mode too which I am not sure how I will use that. Perhaps on my switch when needed. For $13.99 it is worth a try and it should also fit without any trouble...

How do you find the brightness of this light bar? Is it something that can be used for regular DRL, or should it be on a separate switch for usage when necessary?

I have my SPC kit for my 2024 Tacoma Pro and saw on the Rigid site that these lights only use 1 amp, which I would assume would be 2 amps for both. https://www.rigidindustries.com/sr-l-series-off-road-spreader-pod-red-halo-pair-53122.html I am thinking of changing the rear connector pigtail in...

This one looks interesting too and with Amber. It might be tight and not using the brackets. SAMMAN 10Inch LED Light Bar 78W Yellow Spot Flood Combo Beam Driving Off Road Bar Fog Light for Truck Pickup Jeep SUV ATV UTV 2PCS 2 for $35.99 78W https://www.amazon.com/dp/B089SS4DVM I would...

Did you need to remove all the hood scoop components and drill a hole for the wire I would suppose? I wonder if this one would fit which is the same model but is 10" instead of the 7". https://www.amazon.com/dp/B0CV3H8RJD

Which model NLight did you use? What did you do with the grill and the placement of the light bar?