Hood Vibrating Fix! (Weather Stripping / Rubber Trim Seal)

[Iqudayo]

So I got to solve the hood vibration with the help of a member ordered this and installed it no more vibrating hood.

Here is what it looks like installed, got it from Amazon.

Automotive Door Weather Stripping 10Ft Car Door Rubber Edge Trim Seal Strip Gasket with Top Bulb Easy to Install for Car Bus Camper Boat RV Truck Doors and Home Applications

Sponsored

 

[Viper_00]

Thanks! I will have to try this.

 

[Iqudayo]

Thanks! I will have to try this.

It’s a fantastic fix, as I said this is something They can at the factory

 

[TacoFreak]

It’s a fantastic fix, as I said this is something They can at the factory

True, and that makes you wonder why Toyota doesn't just fix this themselves. I saw that Taco sales are up for last quarter, so maybe they just don't care.

 

[Nacho TacoMan]

Link to exact product you purchased please?

 

[Iqudayo]

Link to exact product you purchased please?

This is it

Amazon;
Automotive Door Weather Stripping... https://www.amazon.com/dp/B0BVVRCVB9?ref=ppx_pop_mob_ap_share

 

[frankmig]

Does this hinder air flow or air temp that could affect turbo performance in anybway? There may be a performance reason for why they chose to do it like that.

 

[Brent@ANParts]

Nicely done! I doubt it does too much to affect engine temps, but worth keeping an eye on for a week or two to be safe. Curious if there's a change in temp, if any at all.

 

[Iqudayo]

Does this hinder air flow or air temp that could affect turbo performance in anybway? There may be a performance reason for why they chose to do it like that.

I could always remove the outer ones and keep the center one, that will work as well OCD just kicked in and trying to keep it uniformed.

 

[SnowmanJPS]

I just happened to have some of this at work, how long of a piece did you need? I feel like I don’t need close to 10’

 

[Iqudayo]

I just happened to have some of this at work, how long of a piece did you need? I feel like I don’t need close to 10’

I went with enough to fit between the washer nozzles

 

[TacoFreak]

I went with enough to fit between the washer nozzles

I think that might be enough to stop the shake and I don't see how it would change anything about how air flows under the hood. Let us know how that goes please.

 

[SnowmanJPS]

I went with enough to fit between the washer nozzles

7’ it is, going to give it a try after work

 

[SnowmanJPS]

It’s way easier to get a nice cut off the truck I went with 13 1/2”, 21 3/4” and 8 1/4 in order from left (passenger) to right (driver)

The furthest right one could be longer but looks like it might pull further from the hood and not touch so I didn’t bother to go further, I could change it later for a better look if I choose, I brought 7’ home, there’s still another bit left so if you ordered the 10’ of 1/2" bulb seal from Amazon you could almost do two trucks

Also FYI this type of seal is metal ribbed, you need a decent set of tin snips to cut through it

Edit, finally tested over the speed bumps in my neighbourhood and it seems to soak up 90% of the shake, definitely a huge improvement, I’ll test more this weekend as I’m driving 3 hours down the province

 

[Amorak]

In his pretty much anti Tacoma TRD Pro video, the Car Care Nut pointed out (paraphrase), "Toyota used to always put weather stripping here (like in post), and now they are not here, and you are getting hood shake"
Sheezzz Toyota.

Sponsored